From OpenSCADAWiki
Enter a message name below to show all available translations.
Found 2 translations.
| Name | Current message text |
|---|---|
| h English (en) | [[File:LibsMainUPSCfg.png|right|Configuration.]] {{CntHdr|Configuring and using}} :1. [ [[Special:MyLanguage/Modules/System|DAQ.System]] ] Create a source controller object in the module DAQ.System and set its identifier like to "SYSData". :2. [ [[Special:MyLanguage/Modules/System|DAQ.System]] ] Create a source parameter object in the previous controller object and set its identifier like to "UPS". :3. Create and start a [[Special:MyLanguage/Modules/LogicLev|Logical Controller Object]] or use any presented with the need scheduling properties. :4. Create a [[Special:MyLanguage/Modules/LogicLev|Logical Parameter Object]] and select the template for it. Enable the parameter. :5. In the tab "Template configuration" of the Logical Parameter Object you need to set: :* ''Source object's address'': ::* [ [[Special:MyLanguage/Modules/System|DAQ.System]] ] — to address of the source UPS parameter object (see to step 1) like to "System.SYSData.prm_UPS"; ::* [ Must EP2100 PRO ] — to Serial address of connecting the device like to "Serial.ep21:/dev/ttyUSB0:9600:8N1||500:30". :6. RESULT: When running the controller object (where this parameter was created) and if it was not started, we must obtain in the parameter attribute ''All items (items)'' this object with all the attributes and their properties. In the case of some violations, we will get the corresponding information in the attribute ''Error (err)'', for which you can adjust the attributes of the boundaries of the corresponding violations. To customize some item's description and to place some in DAQ-Attributes, you can edit "Elements definition (defs)" for ones. From the created DAQ-Attributes you can also control writable ones. :7. In the visual interfaces developing of the module [[Special:MyLanguage/Modules/Vision|Vision]] place the frame "[[Special:MyLanguage/Libs/Main_graphical_elements#objProps|Object properties]]" to any page and link its to the parameter object, created in step 4. :8. RESULT: In the runtime of the page you'll get a table with data of the object, notifications about violations in the header and the possibility to set of writable properties. |
| h Ukrainian (uk) | [[File:LibsMainUPSCfg_uk.png|right|Конфігурація.]] {{CntHdr|Конфігурація та використання}} :1. [ [[Special:MyLanguage/Modules/System|DAQ.System]] ] Створити об'єкт контролеру джерела у модулі DAQ.System і встановити його ідентифікатор на кшталт "SYSData". :2. [ [[Special:MyLanguage/Modules/System|DAQ.System]] ] Створити об'єкт параметру джерела у попередньо створеному об'єкті контролера і встановити його ідентифікатор на кшталт "UPS". :3. Створити і запустити [[Special:MyLanguage/Modules/LogicLev|Об'єкт Логічного Контролеру]] або використати будь який наявний з потрібними властивостями планування. :4. Створити [[Special:MyLanguage/Modules/LogicLev|Об'єкт Логічного Параметру]] і обрати цей шаблон для нього. Ввімкнути параметр. :5. У вкладці "Конфігурація шаблону" Об'єкту Логічного Параметру маєте встановити: :* ''Адреса вихідного об'єкту'' ::* [ [[Special:MyLanguage/Modules/System|DAQ.System]] ] — у адресу об'єкту вихідного параметру ДБЖ (дивіться крок 1), на кшталт "System.SYSData.prm_UPS"; ::* [ Must EP2100 PRO ] — у Послідовну адресу підключення пристрою на кшталт "Serial.ep21:/dev/ttyUSB0:9600:8N1||500:30". :6. РЕЗУЛЬТАТ: Запустивши об'єкт контролеру (де створено цей параметр) і якщо він не запущений, маємо отримати у атрибуті параметру ''Всі елементи (items)'' цей об'єкт з усіма атрибутами і їх властивостями. У випадку деяких порушень отримаємо відповідну інформацію у атрибуті ''Помилка (err)'', стосовно чого можете налаштувати атрибути границь відповідних порушень. Для адаптації до користувача деяких описів елементів і для розташування деяких у DAQ-Атрибутах, можете відредагувати "Визначення елементів (defs)" щодо них. Зі створених DAQ-Атрибутів можете також контролювати доступні до запису. :7. У візуальному інтерфейсі розробки модуля [[Special:MyLanguage/Modules/Vision|Vision]] розташуйте кадр "[[Special:MyLanguage/Libs/Main_graphical_elements#objProps|Властивості об'єкту]]" до будь-якої сторінки і зв'яжіть його із об'єктом цього параметру, створеного на кроці 4. :8. РЕЗУЛЬТАТ: При виконанні сторінки отримаєте таблицю з даними об'єкту, повідомленням про порушення у заголовку та об'єкті сигналізації і можливістю встановлення доступних до запису властивостей. |