Difference between revisions of "Translations:Libs/Main graphical elements/19/en"

Latest revision as of 16:28, 12 June 2019

At demo mode present you should into attribute "Procedure play demo" describe demo procedure on internal language OpenSCADA DAQ.JavaLikeCalc. For example bellow led demo procedure of "Dynamic model AGLKS":

stepCur++; stepTm = 20;
//>> Open main mnemo
if(stepCur == 0)
{
	this.pg_1.pg_mn.pg_1.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Main mnemo open.");
}
//>> Open main graphics
else if(stepCur == 1)
{
	this.pg_1.pg_ggraph.pg_1.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Main graphics open.");
}
//>> Setpoint set more for PC KRD1
else if(stepCur == 2)
{
	SYS.DAQ.BlockCalc.Anast1to2node_cntr.PC_КРД1.sp.set(6);
	this.attrSet("tipStatus","The regulator PC_KRD1 setpoint increase.");
}
//>> Open contours group
else if(stepCur == 3)
{
	this.pg_1.pg_gcadr.pg_1.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Contours group open.");
}
//>> Open overview cadr
else if(stepCur == 4)
{
	this.pg_1.pg_gview.pg_1.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Overview frame open.");
}
//>> Open document
else if(stepCur == 5)
{
	this.pg_1.pg_doc.pg_1.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Document open.");
}
//>> Open result graphics
else if(stepCur == 6)
{
	this.pg_rg.pg_rg.pg_1.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Result graphics open.");
}
//>> Open mnemo for KM101
else if(stepCur == 7)
{
	this.pg_2.pg_mn.pg_KM101.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Mnemo KM101 open.");
}
//>> Open graphics for KM101
else if(stepCur == 8)
{
	this.pg_2.pg_ggraph.pg_1.attrSet("pgOpen",true);
	this.attrSet("tipStatus","Graphics КМ101 open.");
}
//>> Open PID-control panel
else if(stepCur == 9)
{
	this.ownerSess().pg_control.pg_ElCadr.attrSet("pgOpenSrc",this.pg_1.pg_mn.pg_1.wdg_PC1.attr("path"));
	this.attrSet("tipStatus","The parameter PC_KRD1 control panel open.");
	stepTm = 1;
}
//>> Open PID-control page
else if(stepCur == 10)
{
	this.ownerSess().pg_control.pg_cntrRegul.attrSet("pgOpenSrc",this.ownerSess().pg_control.pg_ElCadr.attr("path"));
	this.attrSet("tipStatus","The regulator PC_KRD1 control panel open.");
}
//>> Setpoint restore for PC KRD1
else if(stepCur == 11)
{
	SYS.DAQ.BlockCalc.Anast1to2node_cntr.PC_КРД1.sp.set(5.8);
	this.attrSet("tipStatus","The regulator PC_KRD1 setpoint restore.");
}
else { stepCur = -1; stepTm = 0; }